##------------------------------------------------------------------------##
# Debain GNU/Linux tftplilo.conf Installation and Boot configuration.
#

##------------------------------------------------------------------------##
# When installation has completed uncomment the following section and
# add an "ip = a.b.c.d" line to match the IP address of the installed
# system. This will allow you to boot without the installation menu
# appearing.
#
# Note that the installation process will by default install to a hard
# disk. Installation to NFS root is as of yet not supported by this
# version of Debian and debian-installer.

#[crate]
#ip      = a.b.c.d
#ip      = w.x.y.z
#boot    = Boot
#delay   = 3
#prompt  = No

##------------------------------------------------------------------------##
# This section is used by default if there is no section above with a
# matching IP address .
#

[crate]
ip       = any
prompt   = Yes
boot     = Install
boot     = Boot
display  = install-message

[display-install-message]
"\n\n\n"
"               Welcome to Debian GNU/Linux\n"
"\n"
"At the 'LILO Boot:' prompt enter a boot method followed by any\n"
"additional kernel boot parameters that may be required.\n"
"Available boot methods are:\n"
" install - Start the installation procedure (default).\n"
" expert  - Start the installation procedure in expert mode.\n"
" boot    - Boot to the installed NFS root file system.\n"
"\n"
"WARNING: You should completely back up all of your hard disks before\n"
"  proceeding. The installation procedure can completely and\n"
"  irreversibly erase them!\n"
"\n"
"Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent\n"
"permitted by applicable law.\n"

##------------------------------------------------------------------------##
# BVME4000/6000
#

[boot] BVME4000 BVME6000
label       = Install
description = Install Debian GNU/Linux.
restricted  = No
root        = /dev/ram0
kernel      = vme/vmlinuz-bvme6000
ramdisk     = netboot-initrd.gz
append      = ramdisk_size=13000
read-only

[boot] BVME4000 BVME6000
label       = Expert
description = Install Debian GNU/Linux in Expert mode.
restricted  = No
root        = /dev/ram0
kernel      = vme/vmlinuz-bvme6000
ramdisk     = netboot-initrd.gz
append      = ramdisk_size=13000 DEBCONF_PRIORITY=low
read-only

[boot] BVME4000 BVME6000
label       = Boot
description = Boot NFS root file system.
kernel      = vme/vmlinuz-bvme6000
root        = /dev/nfs
append      = nfsroot=/nfshome/%C nfsaddrs=%C:%S:%g:%M:::

##------------------------------------------------------------------------##
# MVME162/6/7 and MVME172/7
#
 
[boot] MVME162 MVME166 MVME167 MVME172 MVME177
label       = Install
description = Install Debian GNU/Linux.
restricted  = No
root        = /dev/ram0
kernel      = vme/vmlinuz-mvme16x
ramdisk     = netboot-initrd.gz
append      = ramdisk_size=13000
read-only

[boot] MVME162 MVME166 MVME167 MVME172 MVME177
label       = Expert
description = Install Debian GNU/Linux.
restricted  = No
root        = /dev/ram0
kernel      = vme/vmlinuz-mvme16x
ramdisk     = netboot-initrd.gz
append      = ramdisk_size=13000 DEBCONF_PRIORITY=low
read-only

[boot] MVME162 MVME166 MVME167 MVME172 MVME177
label       = Boot
description = Boot NFS root file system.
kernel      = vme/vmlinuz-mvme16x
root        = /dev/nfs
append      = nfsroot=/nfshome/%C nfsaddrs=%C:%S:%g:%M:::

##------------------------------------------------------------------------##